Escea IB1100 Installationshandbuch

G8872_3 Installation Manual AUS IB1100 and IB850 Installation Manual AUSTRALIAN EDITION Important: The appliance shall be instal

G8872 _3 Installation Manual AUS 10 The electrical cord (from an extension cord) should pass through the Outer Skin Kit as shown, through the suppli

G8872 _3 Installation Manual AUS 11 11.0 Installing the Flue System: Non-Masonry Timber Frame Cavity: The heater must be flued to the outside via a

G8872 _3 Installation Manual AUS 1212.0 Flue Assembly Secure the Flue spacer bracket to the top

G8872 _3 Installation Manual AUS 1312.1 Installing the Flue Terminal Cut the flue termination to the height specified on the attached “Flue posit

G8872 _3 Installation Manual AUS 14 12.2 The top of the flue must be capped with an appropriate and approved anti down draft cowl. All the required

G8872 _3 Installation Manual AUS 152.6.13 FLUE TERMINALS 2.6.13.1 Location The termination point of a flue shall be located in relation to any ass

G8872 _3 Installation Manual AUS 16

G8872 _3 Installation Manual AUS 1712.4 Fixing the Flue to the Cavity A length of Angle should be attached to the inside of the timber frame cavi

G8872 _3 Installation Manual AUS 18 12.5 Masonry Cavity and Chimney: The heater can be flued with 100mm flexible aluminum ducting in accordance wit

G8872 _3 Installation Manual AUS 19 13.3 This flexible pipe should be attached to the copper supply pipe and the joint tested to e

G8872 _3 Installation Manual AUS 2Note: THERE ARE A FEW THINGS TO CONSIDER BEFORE INSTALLATION • Cavity Dimensions, Clearances, and fitting the Ou

G8872 _3 Installation Manual AUS 20 14.3 Attach the Top-Rear: Attach the top-rear panel to the Sides and Rear panels, with the flanges of the Top-r

G8872 _3 Installation Manual AUS 2116.0 Gas Fireplace Installation: Attached to the base of the Outer Skin Kit are guide rails. The inside edge of

G8872 _3 Installation Manual AUS 22 Step 3: Remove the top of the heater outer shell. Take out the screw from each side (as shown below), lift and

G8872 _3 Installation Manual AUS 23 17.0 Attaching the Flue to the Fireplace: Once the gas fireplace has been inserted into the OSK and

G8872 _3 Installation Manual AUS 24Note: Refer to 13.2 for further gas pipe laying information as per diagram below 19.0 Fixing the

G8872 _3 Installation Manual AUS 25 19.2 Fixing Heater to Wall: The installer must also fix the heater to the sides of the cavity using the bracket

G8872 _3 Installation Manual AUS 26 20.0 IB850: Locating the Log Set After Replacing the Firebox: 1) Remove packaging from around log sets 2) Pl

G8872 _3 Installation Manual AUS 27 IB850 Log & Template Position 4) Line up some of the coals that have been supplied with this

G8872 _3 Installation Manual AUS 2820.1 IB1100: Locating the Log Set After Replacing the Firebox: 1) Remove packaging from around log sets 2) Pl

G8872 _3 Installation Manual AUS 2920.2 Log Replacement: The fire unit should never be used with broken logs. Turn off the fire and allow the unit t

G8872 _3 Installation Manual AUS 3 Contents: Section: • Product Description 1.0 • Creating the Cavity 2.0 • Ventilation

G8872 _3 Installation Manual AUS 30A B C D This is done at the regulator located at the front RH corner of the appliance. This is best done before t

G8872 _3 Installation Manual AUS 3123.0 Fitting the Fascia Panels: To avoid scratches or knocks to the fascia panels of this heater they must be fi

G8872 _3 Installation Manual AUS 3223.1 When installing a 4 sided fascia ensure that the clips that the outer fascia screw into are at the bottom o

G8872 _3 Installation Manual AUS 3325.0 Normal Operating Sounds and Smells; Note: Each time the fire is lit from cold the glass may fog up with co

G8872 _3 Installation Manual AUS 34 26.0 Installation Check List: 1 Ensure there is adequate ventilation in the masonry cavity.__ 2 Ens

G8872 _3 Installation Manual AUS 4• 1.0 Product Description: The Escea IB1100 and IB850 gas fires are designed to be built into a cavity. Both app

G8872 _3 Installation Manual AUS 51.2 Product Dimensions IB850 IB1100 4 Sided Fascia10586373475603655

G8872 _3 Installation Manual AUS 6CAB2.0 Creating the Cavity: The dimensioned drawing below shows the size of opening that must be created to fit t

G8872 _3 Installation Manual AUS 7as the fire’s outer fascia and no less than 10mm thick. Raised hearths can be any size but must also be constructe

G8872 _3 Installation Manual AUS 8300200100150 7.0 Wall Linings: The front mounting flanges of the ‘Outer Skin Kit’ MUST be on top of the FINISHED

G8872 _3 Installation Manual AUS 9 9.0 Corner Installations: If a cavity is to be created in a corner, the following drawings give the minimum size